2n M2M Solution 2N SmartCom - User Manual 1.9.0 Manual de usuario Pagina 24
- Pagina / 149
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
242N TELEKOMUNIKACE a.s., www.2n.cz
®
Caution
Any manual setting is valid until the next change or – Attention!
device power off. does not keep in mind the relay2N SmartCOM
®
settings and restores the default status upon power up.
Set the parameter determining the relay position upon power up to 2
to make your remember the last contact position2N SmartCOM
®
before power off. Refer to the configuration subsections for more
details.
RS-232 and RS-485 / M–Bus Interfaces
Find the interface connectors on the bottom side of . Refer to 2N SmartCOM
®
Subs.
. A 9-pin D-sub connector is used for RS-232 and a 6-pin RJ12 connector is used2.1
for RS-485 or M-Bus in the basic version. Follow the wiring2N SmartCOM
®
instructions on the label. and use a2N SmartCOM
®
PRO 2N SmartCOM PRO ETH
®
3-pin WAGO terminal for bus connection located on the bottom panel next to the power
supply terminals. Follow the wiring instructions on the label.
IP Access
To access via the IP protocol, use a Telnet supporting terminal and2N SmartCOM
®
get connected to the public IP address. must be in2N SmartCOM
®
2N SmartCOM
®
mode 3 , STANDALONE, to provide access to three ports, each of which serves one
interface.
Tip
Port 10000 – helps you configure, control the output relays and
measure quantities on the input circuits.
Port 10001 – works as a data pipe to port RS 232 retransmitting all
RS 232 events to GPRS.
Port 10002 – works as a data pipe to port RS 485 / M–Bus
retransmitting all RS 485 events to GPRS.
Gel–Lead–Acid Accumulator Charger
This function is available in the version only, which contains an2N SmartCOM PRO
®
intelligent charger for an external gel–lead–acid accumulator. Charging is controlled
automatically and terminated when the accumulator has been completely charged. In
the case of power failure, the system is fed continuously by the accumulator and, upon
power recovery, the accumulator is charged automatically. A 6V or 12V accumulator
can be used and charged on condition that the power voltage is 1V higher at least than
the maximum voltage of the accumulator.
- 2N SmartCom 1
- 1. Product Overview 5
- 1.1 Product Description 6
- 1.2 Upgrade 8
- 1.3 Terms and Symbols Used 9
- 2.1 Basic Version Description 11
- 2.2 PRO Version Description 13
- 2.3 Before You Start 15
- 2.4 Mounting 16
- 3. Function and Use 19
- 3.1 Putting in Operation 20
- 3.2 GSM LED Indicator 21
- 3.3 Input and Output Circuits 22
- Output Circuits 23
- IP Access 24
- Real Time Clock 25
- Wireless M–Bus Interface 25
- ZigBee Interface 26
- 3.4 Input Calibration 27
- 4. Configuration by Terminal 29
- 4.1 Configuration 30
- 2N SmartCOM GSM Commands 32
- Port 1 (RS 232) SC Commands 34
- Relay Outputs 36
- ADC – Input Circuits 38
- S0 – Pulse Counting 41
- General Commands 43
- Test Command 46
- 5. Configuration by SMS 58
- INFO SMS 59
- Basic Settings 60
- Relay Control 62
- Error Replies 64
- 6. Terminal Config 66
- Application Details 67
- Application Use 70
- Figure: Ethernet Menu 71
- Figure: IP Access Menu 77
- 7. Control Panel 78
- 7.1 SC Server 79
- Licencing 80
- 7.2 Control Panel 82
- Introduction to Application 84
- Figure: Application Window 85
- Basic Controls 86
- 7.3 Control Panel Use 88
- Connections 90
- Virtual Ports 92
- Settings 94
- Admin Mode 96
- Terminals 99
- Server Settings 101
- Firmware Management 103
- 8. AT API 107
- 8.1 AT API Description 108
- 8.2 Supported Commands 109
- Terminal Connection 111
- Terminal Communication 111
- Port Settings 112
- Terminal Data Reading 113
- 9. User Defined Functions 117
- 9.1 UDF Description 118
- 9.2 UDF Condition Setting 119
- Action Types 121
- Action Parameters 123
- Counters 125
- Error Codes 125
- 10. sc_config 128
- Database Export and Import 129
- Setting Options 130
- 11. Maintenance 134
- 11.2 Factory Default Reset 136
- 11.3 Repairs 137
- 12. Technical Parameters 138
- Power Supply 139
- Relays (Two) 139
- Input Circuits to ADC (Two) 140
- RS232 Interface 140
- Working Conditions 140
- CE certificate 143
- 13. Supplementary 144
- Information 144
- 13.1 List of Abbreviations 145
Relacionado con productos y manuales para Accesorios de comunicación 2n M2M Solution 2N SmartCom - User Manual 1.9.0
Accesorios de comunicación 2n 4G wireless router 2N SpeedRoute - User manual, 18 Manual de usuario
(101 paginas)
(101 paginas)
Accesorios de comunicación 2n OfficeRoute - User manual, 1493 v1.9.0 Manual de usuario
(113 paginas)
(113 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.138 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales