2n Analogue UMTS gateway 2N EasyGate UMTS USB - User Manual de usuario

9 3. EasyGate UMTS Data Status Indication 3.1. Indication LEDs Name Meaning Power supply • Light = EasyGate UMTS Data is powered. • Flashes once

10 Dialing end signaling: • Dialing reception has been terminated. Connection is being established. PIN tone: • Enter the PIN code. • This tone

11 4. USIM Card PIN protection If a USIM card is PIN-protected and the PIN is not programmed in EasyGate UMTS Data, network LED indicates the state an

12 5. Voice function Outgoing and incoming call establishing procedures for an analog telephone are described for illustration. The procedures are the

13 5.3. Automatic Call ("Baby Call") If the Baby Call function is enabled, a pre-programmed period of time is counted down after off-hook. I

14 5.6. Call forwarding For forwarding activation you must specify <Telephone number> the calls will be forwarded to. You may specify <Call t

15 Activation for all call types and specified delay time: <Telephone number> <Delay time> Activation for selected call type

16 To terminate all held calls, or reject waiting call dial: To terminating active call and accept the held or waiting call dial: To place the a

17 6. USB interface You can use HSDPA or GPRS internet access or CSD connection when connecting Your EasyGate UMTS DATA with PC via USB interface. 6.1

18 7.1. Programming Install the EasyGate UMTS Data PCManager software available on the included CD-ROM into your PC. The program is designed for EasyG

Dear customer, Let us congratulate you on having purchased the EasyGate UMTS Data system. This new product has been developed and manufactured to pro

19 8. EasyGate UMTS Data Parameter Programming All EasyGate UMTS Data parameters have such default values that meet most users’ demands and need not b

20 8.2. PC based Programming For programming, connect EasyGate UMTS Data to a PC with a serial cable and make sure that the EasyGate UMTS Data PCManag

21 7. Save data into EasyGate UMTS Data – if EasyGate UMTS Data is not in its special programming mode, you are invited to switch EasyGate UMTS Data o

22 UMTS Date is made in version B only. After connecting EasyGate UMTS Data to PC the program checks the version settings. If the version is set wrong

23 8.3. Parameter Tables All programmable parameters are listed in this section. Each parameter is accompanied with the unit used, function number (if

24 None -EasyGate doesn't send tariff pulse as signaling of call start/end. Call end -EasyGate sends tariff pulse when call ends. Ca

25 Busy tone - cadence Function No.: - Busy tone cadence setting. Setting options: 330/330 ms -cadence 330 ms tone, 330 ms pause 200/200

26 Ringing signal – cadence DATA/Fax Function No.: - This setting doesn’t influence EasyGate UMTS Data. EasyGate UMTS Data doesn’t support Data/Fa

27 8.3.2. FXS routing parameters All parameters related to the number dialed for an outgoing call are arranged in this table. According to the prefix

28 Routing table enable Function No.: 20 Enable the use of the routing table with this parameter. Disabling this parameter you put the table out

User Manual Versions Version Amendments to Earlier Versions 1.00 • The User Manual applies to EasyGate UMTS Data FW Version 2.20K Upgrade The

29 Extra tariff Function No.: - Pseudo tariff metering setting (tariff is based on call duration). The Extra tariff parameter defines transmit

30 Setting options: -Disable -The GSM module logs out of a foreign network and attempts to register again in within 5 minutes. -Enable -EasyGate

31 Credit value position in received SMS Function No.: - If there are more numbers except credit value in text answer (e.g. date, time and so on)

32 8.3.6. Service Parameters Hardware version Function No.: - EasyGate UMTS Data hardware version - for information only (cannot be modified).

33 Initialization of GMS/UMTS & USIM Function No.: 94 Initialization of all parameters related to the UMTS/GSM network and USIM card (except

34 8.3.8. Security Parameters PIN - value Function No.: 40 Fill in the PIN value for automatic PIN entering upon EasyGate UMTS Data power up

35 9. Troubleshooting No LED is on after power up • Check the power supply. All LEDs are on. No call is currently in progress. • EasyGate UMTS Data i

36 10. List of Abbreviations • CLIP - Calling Line Identification Presentation • COM - PC serial port • DTMF - Dual Tone Multifrequency - tone

37 Technical Parameters – UMTS EasyGate: UMTS/GSM: UMTS module, bandwidth UC 864-E UMTS 2100, EGSM 850/900, GSM 1800/1900 MHz UC 864-G UMTS 850/

Packing List An EasyGate UMTS Data delivery contains the following items: Item Number of Pieces EasyGate UMTS Data 1 pc Antenna for direct connecti

CONTENTS 1. EASYGATE UMTS DATA PURPOSE ... 5 1.1. BASIC FUNCTIONS

5 1. EasyGate UMTS Data purpose 1.1. Basic Functions • The primary purpose of EasyGate UMTS Data is to transmit voice between a UMTS or GSM network an

6 2. Installation 2.1. Proper Location • EasyGate UMTS Data is designed for vertical mounting on suspension holes (use the mounting pattern). This pos

7 2.2. External Antenna Connection Screw the antenna enclosed into the SMA antenna connector. Tighten the antenna connector gently with your hand - ne

8 2.4. Connector description USB interface Telephone line RJ 12, 6/2 Power supply connector DC Jack 2,1mm RS232C serial line D-Sub 9 pins 2.